source#####################################
# Akka Stream Reference Config File #
#####################################
# eager creation of the system wide materializer
akka.library-extensions += "akka.stream.SystemMaterializer$"
akka {
stream {
# Default materializer settings
materializer {
# Initial size of buffers used in stream elements
initial-input-buffer-size = 4
# Maximum size of buffers used in stream elements
max-input-buffer-size = 16
# Fully qualified config path which holds the dispatcher configuration
# or full dispatcher configuration to be used by ActorMaterializer when creating Actors.
dispatcher = "akka.actor.default-dispatcher"
# FQCN of the MailboxType. The Class of the FQCN must have a public
# constructor with
# (akka.actor.ActorSystem.Settings, com.typesafe.config.Config) parameters.
# defaults to the single consumber mailbox for better performance.
mailbox {
mailbox-type = "akka.dispatch.SingleConsumerOnlyUnboundedMailbox"
}
# Fully qualified config path which holds the dispatcher configuration
# or full dispatcher configuration to be used by stream operators that
# perform blocking operations
blocking-io-dispatcher = "akka.actor.default-blocking-io-dispatcher"
# Cleanup leaked publishers and subscribers when they are not used within a given
# deadline
subscription-timeout {
# when the subscription timeout is reached one of the following strategies on
# the "stale" publisher:
# cancel - cancel it (via `onError` or subscribing to the publisher and
# `cancel()`ing the subscription right away
# warn - log a warning statement about the stale element (then drop the
# reference to it)
# noop - do nothing (not recommended)
mode = cancel
# time after which a subscriber / publisher is considered stale and eligible
# for cancelation (see `akka.stream.subscription-timeout.mode`)
timeout = 5s
}
# Enable additional troubleshooting logging at DEBUG log level
debug-logging = off
# Log any stream stage error at the specified log level: "error", "warning", "info", "debug" or "off".
# If there is an `akka.stream.Attributes.LogLevels` attribute defined for a specific stream this value is ignored
# and the `onFailure` value of the attribute is applied instead.
stage-errors-default-log-level = error
# Maximum number of elements emitted in batch if downstream signals large demand
output-burst-limit = 1000
# Enable automatic fusing of all graphs that are run. For short-lived streams
# this may cause an initial runtime overhead, but most of the time fusing is
# desirable since it reduces the number of Actors that are created.
# Deprecated, since Akka 2.5.0, setting does not have any effect.
auto-fusing = on
# Those stream elements which have explicit buffers (like mapAsync, mapAsyncUnordered,
# buffer, flatMapMerge, Source.actorRef, Source.queue, etc.) will preallocate a fixed
# buffer upon stream materialization if the requested buffer size is less than this
# configuration parameter. The default is very high because failing early is better
# than failing under load.
#
# Buffers sized larger than this will dynamically grow/shrink and consume more memory
# per element than the fixed size buffers.
max-fixed-buffer-size = 1000000000
# Maximum number of sync messages that actor can process for stream to substream communication.
# Parameter allows to interrupt synchronous processing to get upstream/downstream messages.
# Allows to accelerate message processing that happening within same actor but keep system responsive.
sync-processing-limit = 1000
debug {
# Enables the fuzzing mode which increases the chance of race conditions
# by aggressively reordering events and making certain operations more
# concurrent than usual.
# This setting is for testing purposes, NEVER enable this in a production
# environment!
# To get the best results, try combining this setting with a throughput
# of 1 on the corresponding dispatchers.
fuzzing-mode = off
}
io.tcp {
# The outgoing bytes are accumulated in a buffer while waiting for acknowledgment
# of pending write. This improves throughput for small messages (frames) without
# sacrificing latency. While waiting for the ack the stage will eagerly pull
# from upstream until the buffer exceeds this size. That means that the buffer may hold
# slightly more bytes than this limit (at most one element more). It can be set to 0
# to disable the usage of the buffer.
write-buffer-size = 16 KiB
# In addition to the buffering described for property write-buffer-size, try to collect
# more consecutive writes from the upstream stream producers.
#
# The rationale is to increase write efficiency by avoiding separate small
# writes to the network which is expensive to do. Merging those writes together
# (up to `write-buffer-size`) improves throughput for small writes.
#
# The idea is that a running stream may produce multiple small writes consecutively
# in one go without waiting for any external input. To probe the stream for
# data, this features delays sending a write immediately by probing the stream
# for more writes. This works by rescheduling the TCP connection stage via the
# actor mailbox of the underlying actor. Thus, before the stage is reactivated
# the upstream gets another opportunity to emit writes.
#
# When the stage is reactivated and if new writes are detected another round-trip
# is scheduled. The loop repeats until either the number of round trips given in this
# setting is reached, the buffer reaches `write-buffer-size`, or no new writes
# were detected during the last round-trip.
#
# This mechanism ensures that a write is guaranteed to be sent when the remaining stream
# becomes idle waiting for external signals.
#
# In most cases, the extra latency this mechanism introduces should be negligible,
# but depending on the stream setup it may introduce a noticeable delay,
# if the upstream continuously produces small amounts of writes in a
# blocking (CPU-bound) way.
#
# In that case, the feature can either be disabled, or the producing CPU-bound
# work can be taken off-stream to avoid excessive delays (e.g. using `mapAsync` instead of `map`).
#
# A value of 0 disables this feature.
coalesce-writes = 10
}
# Time to wait for async materializer creation before throwing an exception
creation-timeout = 20 seconds
//#stream-ref
# configure defaults for SourceRef and SinkRef
stream-ref {
# Buffer of a SinkRef that is used to batch Request elements from the other side of the stream ref
#
# The buffer will be attempted to be filled eagerly even while the local stage did not request elements,
# because the delay of requesting over network boundaries is much higher.
buffer-capacity = 32
# Demand is signalled by sending a cumulative demand message ("requesting messages until the n-th sequence number)
# Using a cumulative demand model allows us to re-deliver the demand message in case of message loss (which should
# be very rare in any case, yet possible -- mostly under connection break-down and re-establishment).
#
# The semantics of handling and updating the demand however are in-line with what Reactive Streams dictates.
#
# In normal operation, demand is signalled in response to arriving elements, however if no new elements arrive
# within `demand-redelivery-interval` a re-delivery of the demand will be triggered, assuming that it may have gotten lost.
demand-redelivery-interval = 1 second
# Subscription timeout, during which the "remote side" MUST subscribe (materialize) the handed out stream ref.
# This timeout does not have to be very low in normal situations, since the remote side may also need to
# prepare things before it is ready to materialize the reference. However the timeout is needed to avoid leaking
# in-active streams which are never subscribed to.
subscription-timeout = 30 seconds
# In order to guard the receiving end of a stream ref from never terminating (since awaiting a Completion or Failed
# message) after / before a Terminated is seen, a special timeout is applied once Terminated is received by it.
# This allows us to terminate stream refs that have been targeted to other nodes which are Downed, and as such the
# other side of the stream ref would never send the "final" terminal message.
#
# The timeout specifically means the time between the Terminated signal being received and when the local SourceRef
# determines to fail itself, assuming there was message loss or a complete partition of the completion signal.
final-termination-signal-deadline = 2 seconds
}
//#stream-ref
}
# Deprecated, left here to not break Akka HTTP which refers to it
blocking-io-dispatcher = "akka.actor.default-blocking-io-dispatcher"
# Deprecated, will not be used unless user code refer to it, use 'akka.stream.materializer.blocking-io-dispatcher'
# instead, or if from code, prefer the 'ActorAttributes.IODispatcher' attribute
default-blocking-io-dispatcher = "akka.actor.default-blocking-io-dispatcher"
}
# configure overrides to ssl-configuration here (to be used by akka-streams, and akka-http – i.e. when serving https connections)
ssl-config {
protocol = "TLSv1.2"
}
actor {
serializers {
akka-stream-ref = "akka.stream.serialization.StreamRefSerializer"
}
serialization-bindings {
"akka.stream.SinkRef" = akka-stream-ref
"akka.stream.SourceRef" = akka-stream-ref
"akka.stream.impl.streamref.StreamRefsProtocol" = akka-stream-ref
}
serialization-identifiers {
"akka.stream.serialization.StreamRefSerializer" = 30
}
}
}
# ssl configuration
# folded in from former ssl-config-akka module
ssl-config {
logger = "com.typesafe.sslconfig.akka.util.AkkaLoggerBridge"
}
